My feed water:
- well water with whole house filter for sediment installed, no softener and no chlorinator.
1) 5 micron polypropylene wound
2) 0.5 micron polypropylene fiber
3) 10 micron Carbon Block (CTO).
Output water's
- PH 6.5 - 6.8
- TDS 220ppm - 240ppm,
- Temperatur 26 - 30 Celcius
- turbidity is clear, taste and odor normal (no worry)
RO Unit 100GPD with 4 stage pre filter & 3 post filter + UVC 2GPM.
Pre Filter:
1) Slim Ceramic Filter absolute 0.9 micron
2) & 3) Carbon Block
4) Ceramic Filter absolute 09.micron
Post Filter:
1) Post Carbon CTO
2) Magnetize/hexagonal filter (factory said make water molecul more smaller)
3) Mineral Filter
4) UVC 2 GPM (11 watt philips)
RO water output:
- PH 5.5
- TDS 8 - 10 ppm
- Without mineral filter taste very bitter, after added Magnetize & mineral filter, taste better but still acid.
We have water dispenser (hot,cold & normal), befofe purchased RO units we bought factory mineral bottle (19 liter).
Now we use the bottle and fill it with RO water, put it on dispenser and use it for daily drinking water.
However after a few use (arround 2 -3 liter) the bottle seem to have many foamy all over the wall and it become more till water is empty, its like the oxygen or gas, not sure about it.
The foam also visible in the glass direct from RO faucet, after while it is gone.
Its like my RO produce "drinking soda" .
How to increase RO Water's PH or make water more alkaline?
Or is there treatment to make RO water more alkaline?
Have you ever experience what is the foamy/gas it is? is it bad or good?
Thanks in advance.
- well water with whole house filter for sediment installed, no softener and no chlorinator.
1) 5 micron polypropylene wound
2) 0.5 micron polypropylene fiber
3) 10 micron Carbon Block (CTO).
Output water's
- PH 6.5 - 6.8
- TDS 220ppm - 240ppm,
- Temperatur 26 - 30 Celcius
- turbidity is clear, taste and odor normal (no worry)
RO Unit 100GPD with 4 stage pre filter & 3 post filter + UVC 2GPM.
Pre Filter:
1) Slim Ceramic Filter absolute 0.9 micron
2) & 3) Carbon Block
4) Ceramic Filter absolute 09.micron
Post Filter:
1) Post Carbon CTO
2) Magnetize/hexagonal filter (factory said make water molecul more smaller)
3) Mineral Filter
4) UVC 2 GPM (11 watt philips)
RO water output:
- PH 5.5
- TDS 8 - 10 ppm
- Without mineral filter taste very bitter, after added Magnetize & mineral filter, taste better but still acid.
We have water dispenser (hot,cold & normal), befofe purchased RO units we bought factory mineral bottle (19 liter).
Now we use the bottle and fill it with RO water, put it on dispenser and use it for daily drinking water.
However after a few use (arround 2 -3 liter) the bottle seem to have many foamy all over the wall and it become more till water is empty, its like the oxygen or gas, not sure about it.
The foam also visible in the glass direct from RO faucet, after while it is gone.
Its like my RO produce "drinking soda" .
How to increase RO Water's PH or make water more alkaline?
Or is there treatment to make RO water more alkaline?
Have you ever experience what is the foamy/gas it is? is it bad or good?
Thanks in advance.









Comment